Friday, February 4, 2011

Canh Chua Thái - Tom Yum Kung (Spicy Thai Soup)

Nguyên liệu: (khoảng 4 người ăn)

- Nước dùng gà (mua xương gà 
   nấu làm nước soup hoặc dùng
   hạt nêm để cho vào nước làm
   nước nấu tôm.
- Tôm to 500-600 gr. (loại tôm 
   có đầu hoặc lột vỏ tùy ý)
- Vài nhánh xả lớn (đập dập, 
   cắt khúc)
- 1 đốt Riềng (thái mỏng)
- 5 tép tỏi (đập dập)
- Rau ngò hoặc mùi (rau húng quế)
- Vài lá chanh 
- 3 trái cà chua (bổ miếng cau) 
- Nấm đen, loại nấm đầu tròn, 
   nhỏ, màu đen (loại đóng hộp)
- 2 muỗng canh gia vị nấu canh
   thái (Tom Yum Paste)
- Nước mắm
- 2 quả chanh (vắt lấy nước, ít
   nhiều tuỳ khẩu vị chua), 
- Ít dầu ăn


Tôm, cá hoặc các món hải sản tùy ý

- 1 trái ớt tươi (hoặc 1 muỗng café ớt tỏi trong hũ mua sẵn) 

Cách nấu:

- Cho thật ít dầu ăn vào chảo (món này nấu thanh, không có vị béo), phi thơm tỏi, cho tôm có đầu hoặc tôm đã bóc vỏ (chừa lại cái đuôi trông cho đẹp), vào xào qua (thật nhanh) cho thơm, xúc tôm ra một đĩa riêng.
- Dùng luôn chảo đang nóng đó, bỏ cà chua vào đảo qua, đừng dầm nát cà chua, món này cà chua còn nguyên miếng.
- Nồi nước soup gà đã làm sẵn (hoặc lấy nước lã, bỏ bột nêm từ thịt, có vị ngọt vào làm thành nồi nước để nấu). Cho sả, riềng, nấm, cà chua vào nồi, đun ít phút cho ra nước thơm.
- Cho tôm đã xào sẵn lúc nãy vào nồi nước dùng. Cho 2 muỗng canh gia vị nấu canh thái (Tom Yum Paste) vào. Nêm nếm nước mắm cho vừa ăn. Cho lá chanh, ớt tươi (tương đối cay) đun vài phút, tôm vừa chín tới bắc ra khỏi bếp.
- Bắc nồi ra ngoài bếp, rồi cho rau húng quế hoặc rau mùi vào, khi ăn vắt nước chanh vào soup. 
Nên nhớ món canh chua Thái này sẽ có đầy đủ vị mặn, chua, cay; dậy vị thanh, nước canh hơi đậm, món này ăn nhạt không ngon.

Khi múc ra tô lớn, nên để tất cả các miếng sả, riềng... cho đẹp và hấp dẫn, còn khi ăn không thích thì bỏ lại. Sở dĩ mình không nên băm nhỏ tất cả gia vị như riềng sả... ra vì nó làm canh đục nước.

Nếu Thích có thể trưng bày bằng cách múc vào nồi lẫu càng hay, trông đẹp mắt và tỏa gia vị thơm nồng của món canh Thái. Dùng với bún hoặc cơm và nhớ ăn thật nóng và thật cay mới ngon nhé.

----------------------------------------------------------------------------------------------

Tom Yum Kung 
(Spicy Thai Soup)

    Ingredients:

 3cups chicken stock
 1tablespoon lime juice
 1stalk lemongrass, sliced thinly (tough outer leaves and bulb removed)
 1 1/2teaspoons galanga powder (Thai ginger)
 3kaffir lime leaves, thinly sliced (or one large strip of lime peel)
 3garlic cloves, minced
 1-2small chili pepper, de-seeded and sliced (as hot as you like or mild)
 1medium bell pepper, sliced (any color)
 1/3cup cilantro
 2tablespoons fish sauce
 1 1/2cups shiitake mushrooms, sliced thinly (or any small mushroom)
 12large raw shrimp, shells removed
 1 (11ounce) can coconut milk

Assembling:

  1. Pour stock and lime juice into a deep cooking pot.
  2. Place lemongrass in a food processor and process until finely grated. Add to pot. The bulb can be thrown into the pot for additional flavor (remove before serving).
  3. Add the galanga powder to the pot.
  4. Add garlic, chilies, peppers, and Kaffir leaves (or lime peel). Bring to a mild boil.
  5. Add the mushrooms and shrimp. Gently simmer 'til shrimp is pink.
  6. Turn down the heat to low then add the coconut milk and fish sauce. Taste to adjust seasonings, adding more chilies and/or fish sauce (instead of salt) as desired.
  7. Serve in bowls with cilantro sprinkled over. And on the side, steamed jasmine rice and quarters of fresh lime.

----------------------------------------------------------------------------------------------

 

Tom Yum Kung  (Spicy Thai Soup)

    Ingredients:

 1lb shrimp or chickens, cut up
 4-5fresh kaffir lime leaf (optional)
 1/4cup tomatoes, chopped
 1 1/2cups mushrooms, sliced
 3cups water (you can mix with vegetable orchicken broth)
 1stalk lemongrass, cut into 1/2-inch pieces
 4-5tablespoons fish sauce
 7-8tablespoons lime juice
 2tablespoons red chili peppers, freshly ground (or to taste)
 1tablespoon chili paste, in soy bean oil (Thai name -- Nam Prik Pao, can be found in Asian grocery store)

Assembling:

  1. Pour water into medium saucepan and place over high head on stove; bring to boil and add Kaffir lime leaves & lemon grass; cook for 2 minutes.
  2. Reduce to low heat, add fish sauce, lime juice, fresh ground red chili, and chili paste in soy bean oil.
  3. Add mushrooms & tomatoes; cook for several minutes.
  4. Add shrimp or chicken.
  5. Turn heat to high, do not stir.
  6. When shrimp or chicken is cooked, continue to cook for 2 minutes more.
  7. Serve with hot steam rice.

---------------------------------------

Thai universities face a brave, new world

Writer: Tej Bunnag and Said Irandoust

 

For a long time the education system in Thailand has been facing a dilemma over policies. Reminiscent of the Orientalist versus Anglicist debate which took place in most countries, policy makers in Thailand have also been caught between education inspired by Western universities vis-a-vis the indigenous model.

The new century, however, may render many such debates irrelevant. Advances in technology, new pedagogical techniques and the creation of knowledge societies have catapulted education to a totally different trajectory.

A few trends in higher education are clearly discernible. No single university or institute is in a position to respond to the burgeoning demands of society. The collective demands on higher education are so high that governments are not in a position to meet the requirements. Two of the biggest markets in Asia - China and India - have realised that the market is simply too huge for the governments to serve, and they are actively inviting foreign partners. China was an early starter, and in 2003 it had already invited foreign universities to establish partnerships in China. In March last year, India introduced an act in parliament allowing foreign universities to establish a base in India.

Both China and India are examples of how foreign universities and local universities can collaborate with each other and bring the best in foreign education to meet its local needs.

This trend is visible in Southeast Asia as well. Singapore and Malaysia have already adopted this path. At the Asian Institute of Technology, Thailand already has its first international inter-governmental institute of higher learning. It is time that Thailand moves in and takes the lead in partnering with foreign universities. This has the twin benefit of not only preventing brain drain, but bringing world class education to one's doorstep.

Second, universities have to be innovative and adapt to emerging situations quickly. Institutes of higher learning have to realise that the market can be ruthless when it hires people. Top level companies only hire the best, and if the institutes or universities are not producing graduates who match the market requirements, chances of them getting hired are remote. The private sector on the other hand, has been complaining regarding the under-supply of globally competitive graduates and the lack of skills required by the market place.

The need for universities to launch innovative programmes and partner with industry is now almost mandatory for universities to remain relevant. Experience has shown that when universities fail to innovate, their students remain confined to bookish knowledge and remain unemployable. If students are unemployable when they leave university, then the spectre of the institution becoming irrelevant looms large.

One innovation that can prevent such occurrences of redundancy is the concept of a University of Professions. Such a university seeks to cater towards professions by integrating scientific knowledge and information from various professions. Knowledge often hinges on practical applications. If universities fail to validate the knowledge generated by various professions, then this cache of knowledge would be lost for future generations.

Knowledge is not the exclusive domain of institutes of higher learning. The corpus of knowledge in the private sector, industry and even indigenous knowledge is so huge that even documenting it would be a gigantic task for universities.

But the task of universities does not end in merely documenting and validating this corpus. As innovators, they need to delve deeper and build further, generating more knowledge.

To be able to achieve this goal, universities need to partner not just with the private sector, but also with communities who are the repository of indigenous knowledge. A two-way relationship is required and universities need to respond by giving them something in return. For the private sector, the relationship could be in the form of better trained graduates. In the case of communities, universities can help them in solving their problems and come up with innovative solutions. These solutions can be based on the collective wisdom of the community, coupled with the application of cutting-edge technology brought to them by universities. Such partnerships could collectively further the cause of creating a knowledge society.

Apart from partnering with global universities and local partners, a third significant way universities could innovate is to take the lead in forging financial partnerships. Finance is a key issue for universities all over the world, and with the decline in funding from traditional sources; they have to be innovative in tapping fresh resources. Funding from governments and international agencies to institutes of higher learning is no longer guaranteed. Lack of government finances has reached such a stage that 71 public universities in Pakistan have stated that unless the government releases funds, they will be forced to shut down.

An alternative model is associating all partners including the government, the private sector as well as the universities at one platform. The model need not be a straight three-way relationship but could involve more than one university, or more than one private partner.

The modalities of such a partnership will have to be tailored to the needs of the university. If the university wishes to establish a branch campus in a new country, then local partners and the local government could be considered as possible partners. Both foreign and local investors can be tapped for financing the operations.

The days when one single financial model could be applicable to all are over. One size fits all is no longer valid in universities. For partnering with the private sector, funding can be tapped from not just the private sector but also the beneficiaries. The public-private partnership model has been used extensively by governments, particularly in the field of infrastructure.

An example is the Partnership Victoria initiative by the state government of Victoria in Australia which was launched 10 years ago. Universities have been very active in this initiative.

The initiative came from the government which decided to adopt public-private partnerships for provision of public infrastructure and related ancillary services. So far there are 21 "Partnership Victoria" projects with a capital investment worth A$10.5 billion (300.5 billion baht). Since 2003, "Partnerships Victoria" projects have accounted for approximately 10% of annual public asset investment commitments. Their project on Biosciences Research Centre Project valued at $288 million has partners from government, universities as well as the private sector. The Department of Primary Industries, La Trobe University and three private sector partners have an agreement to create a new world-class facility for agricultural biosciences research and development.

Innovations require new thinking and a critical approach. For universities in Thailand to stop being imitators of the west, it is time to actively search for innovative solutions. This is the era of partnership, but even to partner with the west, universities have to find innovative ways.

Tej Bunnag, a former foreign minister, is the chairman of Board of Trustees of the Asian Institute of Technology.

Said Irandoust is AIT president.

http://www.bangkokpost.com/opinion/opinion/220396/thai-universities-face-a-brave-new-world

 

 

Effect on Shear Strength Due to Various Water Content in Clay Soil - A Proposal


Effect on Shear Strength

Due to Various Water Content in Clay Soil

Proposal in civil engineering regarding to clay soil.


This research is focusing on clay soil. The shear strength that is or will be developed by each soil type is different. Shear strength of soil is able to influence the stability of buildings structure. Soil with high shear strength will be able to support buildings structure without failing. Otherwise, the structure will not be stable and side effects will occur either in short term or long term depends on the shear strength. That is why research regarding to shear strength should be carried out to ensure the capability of soils in supporting loads.

The shear strength of soil depends on the water content. Most geotechnical failures involve a shear-type failure of soil. This is due to the nature of the soil, which is composed of individual soil particle that slide when the soil is loaded. The shear strength parameters of soil are known as cohesion, c and angle of friction, Ø. The higher values of cohesion, c and the angle of friction, Ø is higher the shear strength of the soil.
Clay soils can be classified into four conditions according to the amount of water content. They are solid, semisolid, plastic and lastly liquid [1]. The continuous increment of water content will change solid clays soil to semisolid, followed by plastic and liquid. This process not only changes the condition of clay soils, it also weakens the cohesion value of the soil.
The variations in water content of clays are important for a wide variety of reasons. They affect the engineering properties of the soil and thus the building design. For the contractor, the effect can be more prosaic but very important. For example, the jobsite that is dry and easy to move construction equipment about can become a quagmire if enough rain raises the water content of the soil towards and beyond the liquid limit. This may necessitate matting in order to move equipment around, or even affect the type of equipment that is brought on site. The contractor must be prepared for this type of change if conditions are not the same as when the job was bid or began [9].
Very soft to medium clays are very troublesome when they must be supported or excavated and often are unsatisfactory materials for temporary foundations in shoring systems [9]. In brittle soils, yielding may lead to the formation of shear slip surface, over which sliding movement takes place, e.g. landslips, rotational slope and excavation failures. Measures of shear strength are required in the analyses and design of geotechnical structure, such as foundations, retaining walls, earth slopes and road bases [2].

Any change in the ambient conditions will bring about a change in moisture content. If water is taken in a swelling, pressure will be exerted and the volume will tend to increase. Shrinkage will take place if the adsorbed layer is compressed, forcing water out or if suction reduces the moisture content. The swelling potential of clays is very high. In soil masses in general, shrinkage manifests itself as a series of polygonal cracks emanating downward from the surface [2]. Base on the statements, shows that the amount of water content may influence the stage of soils strength.

The main objectives of this study are:
 
  1. To determine the strength of clay soil resulting to the change of water content
  2. To determine the percentage of water content needed in clay soil to perform maximum shear strength

The chosen location for this research is RECESS which is located in KUiTTHO’s campus in about 20 km from the Batu Pahat town center towards Ayer Hitam. The scope of this study is to determine the shear strength of clay soil according to the water content. It includes of disturbed and undisturbed samples. Samples will be taken at depth of 1.5 meters from the surface. There are 31 samples will be needed. The total of 21 samples will be used for direct shear test, 3 samples for free swell test and the other 7 samples will be used for vane shear test.
The percentages of water content that will be involved in both tests are starting from 15% until 65% with gap of 10%. Clay soil with optimum water content will produced the highest shear strength.
 
Importance and Contribution of Study
 
In producing buildings, there are many factors that should be considered. One of them is the capability or strength of soils in supporting loads. Any failure that happens to supporting soils will affect the building structures. This aspect is also important in process of digging and removing soil in order to prepare a site for construction and services. The problems here are closely related those of support. In the case of both natural and built slopes (embankments), it is necessary to determine their intrinsic ability for self-support. Problems of shear failure, in which possible collapse mechanisms are investigated where rupture surfaces develop due to the shear strength of the soil being exceeded.
Based on the research that will be carried out, graph of shear strength versus percentage of water content will be plotted. From this graph, the suitable percentage of water content to perform a high shear strength soil can be determined. This information helps engineers in estimating the load that can be transferred to the clay soil. However, the achieving results are limited for clay soil in RECESS KUiTTHO because the properties, behaviour and structures of clays are different base on area.


Study Area

 
This research is focusing on clay soil. It includes of soil investigation for the purpose of ground improvement. Clay soil will be investigated from the aspect of shear strength. There are many factor influences the level of shear strength. One of them is the percentage of moisture content. That is why the moisture content in clay soil will be investigated to find out their capability in changing the shear strength of clay soil.

Literature Review


The term soil conveys varying shades of meaning when it is used in different contexts. To a geologist it describes those layers of loose unconsolidated material extending from the surface to solid rock, which have been formed by the weathering and disintegration of the rocks themselves. An engineer, on the other hand, thinks of soil in terms of the work he may have to do on it, in it or with it. In an engineering context soil means material that can be worked without drilling or blasting. Pedologists, agriculturalists, horticulturalists and others will also prefer their own definitions [2].
For engineering purposes soil is best considered as a naturally (mostly) occurring particulate material of variable composition having properties of compressibility, permeability and strength. All soils originate, directly or indirectly, from solid rocks and these are classified [2]. According to McCarthy, in nature, soils are made up of particles of varying size and shape. To distinguish between soil where size cannot be visually discerned (the particles are too small), an additional property, plasticity is used as criterion. Study has proved that a soil’s important behavioural properties are not always controlled by particle size and plasticity. Soil structure and mineralogical composition and their effect with water, may also have significant influence on the properties and behaviour deemed important for design and construction [8].

Clay Soil


The most significant properties of clay are its cohesion and plasticity. If when pressed together in the hands at a suitable moisture content the particles stick together in a relatively firm mass, the soil shows cohesion. If it can be deformed without rupture (i.e. without losing its cohesion), it shows plasticity. Clay dries more slowly than silt and slicks to the fingers; it cannot be brushed off dry. It has a smooth feel, and shows a greasy appearance when cut with a blade. Softer consistencies behave rather like butter, and harder consistencies like cheese. Dry lumps can be broken, sometimes with difficulty, between the fingers, but cannot be powdered. A lump placed in water remains intact.

Clay does not exhibit dilatancy. Lumps shrink appreciably on drying, and show cracks which are the more pronounced the higher the plasticity of the clay. At a moisture content within the plastic range, clay can easily be rolled into threads 3mm diameter which for a time can support their own weight. Threads of high-plasticity clay are quite tough; those of low-plasticity clay arc softer and more crumbly [12].

Properties of Clays


Because of the small particle diameter and plate-like shape of clays, the surface area to mass ratio is much greater than in other soils. This ratio is known as the specific surface. For example, montmorillonite has a specific surface of about 800 m2/g, which means 3.5 g of this clay has a surface area equal to that of a football field.
The large specific surface of clays provides more contact area between particles, and thus more opportunity for various interparticle forces to develop. It also provides more places for water molecules to attach, thus giving clays a much greater affinity for absorbing water. Some clay can easily absorb several times their dry weight in water. The interactions between this water and the clay minerals are quite complex, but the net effect is that the engineering properties vary as the moisture content varies. For example, the shear strength of a given clay at a moisture content of 50% will be less than at a moisture content of 10%.

Formation of Clay Soils


On a slightly larger but still microscopic scale, clay minerals are assembled in various ways to form clay soils. These microscopic configurations are called the soil fabric, and depend largely on the history of formation and deposition. For example, a residual clay, which has weathered in-place and is still at its original location, will have a fabric much different from a marine clay, which has been transported and deposited by sedimentation. These differences are part of the reason such soils behave differently [10].
Although we sometimes encounter soil strata that consist of nearly pure clay, most clays are mixed with silts and/or sands. Nevertheless, even a small percentage of clay significantly impacts the behaviour of a soil. When the clay content exceeds about 50 percent, the sand and silt particles are essentially floating in the clay, and have very little effect on the engineering properties of the soil [10]

Plasticity of Clay


Because of the controlling importance of the effect of surface activity on the behaviour of fine grained soils, description of these materials by reference to their particle sizes is practically meaningless. The practical distinction between silt and clay is made, not on the basis of an arbitrary size distinction, but on the basis of material behaviour in the presence of water. The consistency of fine soil varies according to the amount of water present. Completely dry, the soil may be hard (solid), while at high water contents it may be almost a slurry (liquid). Intermediate states of consistency are semisolid and plastic states. A plastic material is one that deforms readily without cracking or rupture. The boundaries of these states of consistency are defined in terms of soil water content [9].


Different soils may be distinguished by their plasticity characteristics because these characteristics vary with surface activity of the constituent particles. The more active soils (claylike) are more plastic than the inactive soils (silts). This phenomenon may be explained by examining the nature of the water near the surface of a clay particle. Since water’s molecular structure is dipolar, the water near the clay particle is effectively immobilized by the surface charge. It is adsorbed and may be considered essentially solid. As distance from the particle surface increases, the orientation of water is reduced in degree until, at the boundary of the particle’s influence (limit of diffuse double layer), the viscosity is that of free water. With an abundance of water, soil particles would be separated by free water and the mixture would be fluid. As the amount of water decreases, the particles are separated by increasingly stiffer water. The mixture becomes like a solid. The soil water system, therefore, has a range of water contents over which it may be plastic. Changing the chemical composition of the constituent phases (soil type or fluid) causes a change in the plasticity range or the plasticity index. This permits to distinguish among soils on the basis of their plasticity [9].

Expansion of Clays


The generic name for clay minerals that swell (expend) as change in soil water occur is smectite. Clays expand in volume if the soil water content is below a stability value when becomes available. The volume change is related to the thickness and mobility of the water film adsorbed onto or surrounding the clays particle, being increased relatively easily during natural wetting conditions. Probably most of swelling that occurs is due to water moving in. A requirement for significant swelling is that the soil have many fine pores in the 0.001 mm to 0.002mm range. Pores of this size permit rapid acceptance.
The expensive force created by a clay undergoing an increase in water content and volume can be considerable, being capable of lifting heavy structures and imposing lateral pressure that can move retaining walls and basement walls. Swelling pressures in excess of 500 kPa have been measured. High swelling pressures can occur even in already high-moisture clays if additional water is adsorbed. Damage to structure can result when a clay swells.

Shear Strength Theory


The strength of soil is a variable and elusive property. Strength characteristics of some materials are represented by concepts such as yield point or tensile strength. For compacted fills, engineers deal with soils as they are in nature. Because they are not manufactured products, variations in properties are the rule, not the exception. They are natural materials, and in most cases engineers use what is available, adjusting designs and working methods to accommodate conditions [9].
Strength is the measure of the maximum stress state that can be induced in a material without it failing. Although strength can be stated in terms of compressive stress or tensile stress, fundamentally it’s the ability to sustain shear strength that provides strength. The shear strength of a soil, τ is the internal resistance per unit area that the soil mass can offer to resist failure and sliding along any plane inside it. The shear strength of a soil is indicative of the stability and strength of the soil under various conditions of loading, compaction, and moisture content [2].
The shear strength of a soil is the maximum resistance which it can offer to shear stress. When the maximum has been research the soil is regarded as having failed, its strength having been fully mobilized. However, the shear strength value determined experimentally is not a unique constant which is characteristic of the material but varies with the method of testing [13].
The stress on any plane surface can be resolved into the normal stress, σn, which acts perpendicular to the surface and the shearing stress, τ, which act along the surface, the magnitude of the resistance being given by Coulomb’s equation:
τ = c + σn tan Ø
Where,
τ = shear strength of soil
c = cohesion
σn = normal stress
Ø = angle of friction


Shear Strength of Clays

The shear strength of clays depends not only on the soil type and composition, but also on factors related to the mineralogy, grain, size and shape, adsorbed water and water chemistry of the clay minerals present. Shear strength also depends to a great extent upon the initial moisture content of the clay and the rate at which the soil structure can expel or take in water during a test.
In a shear test on a particular type of clay the three factors which are of the greatest significant here are:
  1. the water content (expressed in terms of liquidity index);
  2. the degree of saturation – whether fully saturated or partially saturated;
  3. the rate of shear displacement in relation to the permeability of the soil – whether “quick” (allowing no drainage), or “slow” (allowing full drainage, i.e. the dissipation of any excess pore water pressure set up during shear).

The undrained shear strength of saturated plastic clays is usually determined from compression tests. The shearbox test being less satisfactory for these soils. However their shear strength can be measured directly by the vane apparatus [11]. Clay soils are cohesive in that they possess some strength at zero normal pressure. Consequently, their strength envelope looks like that shown in Figure 2.3. The slope of the strength envelope depends greatly on drainage conditions as the clay is being loaded. For most short-term loading conditions, the usual situation during construction, the slope of the strength envelope is near zero if the clay is saturated. The strength of the clay is, therefore, expressed by the cohesion term, c [9]. For a given clay, unconfined strength or cohesive strength will depend strongly on the water content. Table 7.2 indicates typical ranges of strength corresponding to standard nomenclature for soil consistency. Soils of stiff to hard consistency seldom present problems when encountered in construction [9].



Moisture Content


Naturally occurring soils nearly always contain water as part of their structure. The moisture content of a soil is assumed to be the amount of water within the pore space between the soil grains which is removable by oven drying at 105-110°C, expressed as a percentage of the mass of dry soil. By “dry” is meant the result of oven drying at that temperature to constant mass, usually for a period of about 12-24 hours. In non-cohesive granular soils this procedure removes all water present.
There are several ways in which water is held in cohesive soils, which contain clay minerals existing as plate-like particles of less than 2 μm across. The shape and very small size of these particles, and their chemical composition, enable them to combine with or hold on to water by several complex means [12]. For the purpose of routine soil testing, moisture content relates only to the water which is removable by oven drying at 105-110°C. Moisture content is usually expressed as a percentage, always on the basis of the oven-dry mass of soil.


Methodology
Research methodology is used to described the overall work plans of the research for the whole semester. It is normally written in flow chart that can be easily to read and understand.
Research flow chart is a guideline that will be followed throughout the research to achieve the best result as shown below.
  1. Research Title
  2. Literature Review
  3. Selection of Research Area
  4. Sample Preparation for Laboratory Test
  5. Laboratory Test
    1. Undisturbed sample
      1. Direct Shear Test
      2. Vane Shear Test
      3. Moisture Content Test
      4. Free Swell Test
    2. Disturbed Sample
      1. Direct Shear Test
      2. Vane Shear Test
      3. Moisture Content Test
  6. Data Collection
  7. Data Analysis
  8. Conclusion and Recommendation


Moisture Content Test (BS 1377: Part 2: 1990: Clause 3)

The standard method that will be used for this test is the oven-drying method and this is the procedure recommended for a soils laboratory.
This moisture content test includes of disturbed and undisturbed sample. Undisturbed sample is needed to determine the actual moisture content of sample taken from the research area. To change the percentage of water for the purpose of this study, disturbed sample will be used. The percentage of water will be increased from 15% to 65% with gap of 10%. To determine the mass of water needed to produce 15% until 65% of water content, the following equation can be used:
w (%) = mw x100
mp
where;
w = moisture content
mw = loss of moisture
mp = dry mass


Free Swell Test


About 50g of undisturbed sample will be needed to carry out this test. Because “free swell” is defined as the change in volume of the dry soil expressed as a percentage of its original volume, it can be calculated from the equation:
free swell = V – 10 x 100%
10
where;
V = volume of settled solids

Direct Shear Test (BS 1377: Part 7: 1990: Clause 4)


The direct shear test apparatus for performing single shear is essentially a rectangular or circular box having separated lower and upper halves. For this research, a rectangular shearbox will be used.
In the standard type of apparatus, the box is 60 mm x 60 mm. Both disturbed and undisturbed sample will be used in this test. Three different loads will be applied as the vertical load. They are 1.25 kg, 2.5 kg and 3.75 kg with 7 different samples for each load. The straight-line equation for the limiting shear stress that suggested by Coulumb in 1776 is given below:
τ = c + σn tan Ø
Where;
c = apparent cohesion (assumed to be constant)
σn = normal stress or slip surface
Ø = angle of friction (or angle of shearing resistance)

Vane shear test


The vane shear test consists of inserting a vane into the clay soil and then rotating it by applying a torque [14]. The torque is measured and for a known-size vane, is easily related to the shearing strength of the clay soil. The equation for the applied torque is given by:
T = cu πhd x d + 2π d2 x d
2 4 3
where;
T = applied torque
cu = undisturbed undrained strength
h = height of blade
d = width of blade
Hence cu = T
(1/2) πd2 [h + (1/3)d]
This research basically study on the shear strength of clay soil with certain water content. It includes of swelling analysis, shear strength analysis and water content analysis. The purpose of shear strength analysis is to ascertain the suitable water contain needed for clay soil in RECESS KUiTTHO to perform optimum shear strength.

Shear Strength of Clay Soil in Recess kuittho


At the end of the study, the highest shear strength that clay soil in RECESS KUiTTHO is able to produce can be determined according to the percentage of water content that had been applied in the range of 15% until 65%. Meanwhile, the percentage of optimum moisture content can also be identify in producing the highest shear strength clay soil for the purpose of load supporting such as building structure and so on. As conclusion, the objectives of this research will improve the original shear strength of clay soil in RECESS KUiTTHO.



References

Abdul Rahman Mahamood (1997). “Unsur Mekanik Tanah untuk Jurutera Awam
dan Jurutera Lombong.” Smith, G.N. Dewan Bahasa dan Pustaka.

Abramson, L. W. (1996). “Slopes Stability and Stabilization Methods.” Canada: John
Wiley & Sons, Inc.

Aminaton Marto, Fatimah Mohd Noor dan Fauziah Kasim (1993). “Mekanik Tanah.”
Edisi keempat. Craig, R.F. Unit Penerbitan Akademik UTM.

Bardet, J. P. (1997). “Experimental Soil Mechanics.” New Jersey: Prentice-Hall, Inc.
Bell F. G. (2000). “Engineering Properties of Soils and Rocks.” 4th. ed. Blackwell
Sciene Ltd.

Bujang K. Huat, Ahmad Jusoh dan Shukri Maail (1991). “Pengenalan Mekanik
Tanah.” Kuala Lumpur: Dewan Bahasa dan Pustaka.

Capper, P. L. and Cassie, W. F. (1971), “The Mechanics of Engineering Soils.”
London: E. & F. N. Spon.

Cernica, J. N. (1995). “Geotechnical Engineering Soil Mechanics.” United State:
John Wiley & Sons, Inc.

Coduto, D. P. (1999). “Geotechnical Engineering Principles and Practices.” New
Jersey: Prentice Hall, Inc.

Craig, R. F. (1990). “Soil Mechanics.” 3rd. ed. England: Van Nostrand Reinhold Co.
Ltd.

Erni Haryati binti Samsudin (2003). “Kajian Kekuatan Ricih Tanah Liat Berkelodak
di Kuittho Berdasarkan Kandungan Lembapan.” Kolej Universiti Teknologi
Tun Hussein Onn: Tesis PSM.

Fahrizal bin Mohd Abdoh (2001). “Keadaan-keadaan Tanah Jelekit yang
mempengaruhi kepada Penggunaan Cerucuk.” Institut Teknoligi Tun Hussein
Onn: Tesis PSM.

Hanimah binti Masbot @ Masbor (2004). “Shear Strength Charecteristics of Silty
Clay Soil.” Kolej Universiti Teknologi Tun Hussein Onn: Tesis PSM.

Hayazi bt. Hanafi (1996). “Ciri-ciri Kejuruteraan Endapan Tanah Liat Lembut di
Batu Pahat (ITTHO).” Institut Teknologi Tun Hussein Onn: Tesis PSM.

Head K. H. (1988). “Manual of Soil Laboratory Testing.” Vol. 2. London: Pentech
Press Limited.

Head K. H. (1992). “Manual of Soil Laboratory Testing Part 1.” 2nd. ed. London:
Pentech Press Limited.

Peck, R. B., Terzaghi, K and Mesri, G. (1996). “Soil Mechanics In Engineering
Practice” 3rd. Ed. Canada: John Wiley & Sins, Inc.

Schroeder, W.L., Dickenson, S.E. and Warrington D. C.(2001). “Soils in
Construction.” 5th. ed. New Jersey: Prentice Hall, Inc.

Simons, N. and Menzies, B. (2001). “Foundation Engineering.” 2nd. ed. Britain:
MPG Books, Bodmin.

Spigolon, S. J. (2001). “Goetechnical Engineering.” New York: The McGraw-Hill.
Whitlow, R. (2001). “Basic Soil Mechanics.” 4th. ed. England: Prentice Hall.

 

Xin chữ đầu xuân - Đôi điều suy ngẫm

Lê Thị Chiêng

Trong những năm gần đây ở một số thành phố lớn của Việt Nam như Hà Nội, Hồ Chí Minh phổ biến hiện tượng xin chữ đầu xuân. Việc làm này được cho là nét đẹp văn hóa. Thường là từ mùng 2 Tết, mọi người đã bắt đầu kháo nhau đi xin chữ. Từ người lớn tuổi cho đến thanh niên, học sinh. Việc xin chữ đầu năm đã trở thành một trào lưu của người trẻ tuổi, tạo thành cái gọi là văn hóa chơi chữ mới. Những con chữ như "rồng bay phượng múa" hiện lên qua các nét cọ điêu luyện khiến cho việc xin chữ, ngoài ý nghĩa xin được chữ, còn là để thưởng thức khả năng viết chữ đẹp của những người cho chữ.

Xưa, những người được mọi người xin chữ là những nho sĩ, những thầy giáo, thầy đồ có tiếng hiền tài, đức độ, học rộng biết nhiều, viết chữ đẹp. Người xin chữ vừa mong được phúc của người cho chữ, vừa mong xin được chữ đúng với tâm nguyện phấn đấu của gia đình, bản thân. Có người xin chữ Lộc, cũng có người xin chữ Tài, chữ Phúc, chữ Tâm.

Ngày nay, người trẻ tỏ ra là những người chuộng chữ nghĩa nên đầu năm rủ nhau đi xin chữ. Cũng có thể đôi khi chỉ là sở thích được sở hữu một vật mang tính chữ nghĩa để treo trong nhà. Nhưng phổ biến hơn cả là tâm lý cầu mong chữ đem lại thứ mình mong muốn. Chẳng hạn, những người đi học thường xin chữ Trí, Tài, Nhẫn. Người buôn bán xin chữ Lộc, chữ Tín. Người làm quan chữ Danh… Để cho gia đình người ta thường xin chữ Phúc, Lộc, Thọ, Tâm.

Vào ngày mùng 2 Tết, ở các phố Hà Nội như Bà Triệu, Lý Thường Kiệt, Văn Miếu,... thường bắt đầu diễn ra hoạt động cho chữ đầu năm. Đặc biệt ấn tượng nhất là ở Văn Miếu Quốc Tử Giám, nơi được coi là trung tâm học vấn từ xưa. Ở đây, không khí náo nhiệt bởi những người đến xin chữ, đông đúc và hồ hởi. Phần lớn người xin chữ dạo khắp, ngắm nghía, kén chọn như đi xem hàng rồi dừng lại nơi bắt gặp cái chữ bắt mắt và quyết định xin. Người xin thích chữ gì, người viết làm ra chữ đó. Cả người làm ra và người xin đều chú trọng đến mặt nghệ thuật viết chữ hơn là bản thân con chữ. Nói cách khác, đa phần người đi xin chữ giống người mua tranh và người viết giống người vẽ tranh, hầu như ít ai quan tâm đến sức mạnh tinh thần của con chữ. Mặc dù vậy, họ vẫn vui hân hoan khi xin được chữ như ý muốn, cầu mong một năm mới an khang, vạn sự như ý.

Vậy xin chữ như thế nào để có được sức mạnh của nó chứ không chỉ là bức tranh để ngắm hay vì theo mốt thời đại?

Xin chữ là thể hiện tâm nguyện của sự học. Bởi lẽ chỉ có học mới được chữ. Chữ không phải là thứ có thể đem cho, tặng (thậm chí) bán như hiện nay. Những cái được gọi là chữ bày la liệt trên phố Bà Triệu hay Văn Miếu Quốc Tử giám thực chất chỉ là “từ” chứ không phải “chữ”. “Từ” là thứ có hình tượng, âm tiết có thể viết ra để đọc, nói ra để nghe. Thực chất tất cả những cái gọi là chữ hiện nay mọi người đi xin chỉ là từ. Nhưng chữ thì phải học mới có. Xưa nay chỉ nói học chữ có nói học từ đâu. Thế nào là học chữ?

Học chữ không phải là biết đọc biết viết. Nếu chỉ biết đọc, biết viết thì mới là biết từ chứ chưa phải có chữ. Học để có được chữ phải qua được 3 cấp độ: Biết – Rõ – Minh.

  • Biết là viết và đọc được hình tượng của chữ (hay là từ).
  • Rõ là hiểu được tác dụng của chữ để rèn luyện tu dưỡng bản thân nhằm đạt (có được) chữ.
  • Minh là vận dụng được chữ, tức phát huy tác dụng của chữ.

Bởi vậy, muốn có chữ thì phải học chứ không thể xin. Vậy thì sao lại có tục xin chữ như đã nói ở trên?

Trước hết xin chữ là để học, để tu rèn chứ không phải để có cái treo trong nhà. Muốn vậy cần phải biết vào thời điểm xin chữ, người đi xin cần học chữ gì. Song le, người đi xin lại không biết điều đó mà chỉ xin cái chữ mình muốn, thể như có được cái từ (vẫn nhầm tưởng chữ) là có chữ. Vì vậy người cho (tạo duyên) chữ phải biết chữ họ cần mà trao cho phù hợp . Nói cách khác, người cho chữ là người phải biết cho ai chữ gì họ cần chứ không phải cho chữ họ muốn. Tại sao vậy? Tại vì có rất nhiều cái muốn nhưng lại không phải là cái cần. Cái muốn là ngọn, cái cần là gốc. Chẳng hạn, người buôn bán muốn xin chữ Lộc (một vốn 4 lời), nhưng người cho chữ lại thấy họ cần chữ Tín, bởi vì họ đang thiếu đức tín thì không thể cho chữ Lộc. Mục đích cao cả của học chữ là để thành Người. Nếu không vì mục đích này thì cho chữ chỉ giúp việc buôn bán biến người kia thành con buôn chứ không thể là người buôn hay nhà buôn được.

 

Để cho chữ đúng người cần, người cho chữ phải minh chữ và có khả năng trực giác. Chỉ bằng trực giác thì mới “nhìn” thấu được đối tượng xin là ai và cái gì cần cho họ. Trực giác chính là Thầy. Đây là lý do người đời gọi những người cho chữ là thầy. Chữ Thầy là để nói đến trực giác, trí tuệ chứ không phải tri thức học được của người cho chữ. Người có trí thức không hẳn là người trí tuệ nhưng người có trực giác là người trí tuệ. Người có trí tuệ là người có Chữ, người có nhiều tri thức chưa chắc đã là người có nhiều chữ. Phải có Chữ mới cho được Chữ, nếu không có lấy gì mà cho. Người có tri thức nhưng không có trí tuệ (tức không có Chữ) thì chỉ cho được tri thức chứ không có Chữ để cho. Ví dụ muốn cho người khác chữ An thì bản thân người cho phải có chữ An. Nếu người cho chữ bất an thì lấy đâu ra an mà cho người khác. Cho nên xin chữ là xin cái Trí tuệ của người cho chữ được gửi vào từng nét chữ chứ không phải một bức họa chữ đơn thuần. Chỉ có trí tuệ mới dẫn dắt con người thành Người. Nói như vậy không có nghĩa là cứ nhận được Chữ là trở thành người có chữ. Như trên đã nói, muốn có chữ phải học tập, rèn luyện, phải qua thử thách. Vậy việc nhận chữ có ý nghĩa gì?

Người cho chữ đúng nghĩa như nói ở trên giống như người tạo duyên cho người nhận chữ được khởi duyên. Tạo duyên giống như cho hạt giống tốt. Hạt giống đó đảm bảo nảy mầm nhưng nó phát triển ra sao lại phụ thuộc vào người chăm sóc nó. Giống tốt nảy mầm nhưng không được chăm sóc tốt nó vẫn bị thui chột. Do vậy, người nhận chữ phải dày công tu dưỡng, rèn luyện phấn đấu cho có chữ, nếu không thì “chữ thầy lại trả thầy”. Xin chữ trở nên vô nghĩa.

Hiện nay hiện tượng xin chữ như một thú vui, một cái mốt của thanh niên hơn là thực sự “tìm thầy học chữ”. Người viết miệt mài, cố gắng viết cho được nhiều, người xin thì chọn chữ mình thích rồi mang về treo trong nhà, có khi cả năm không biết có được mấy lần nhớ đến nó. Nơi xin và cho chữ chẳng khác nào một phố thương mại chuyên về những bức họa chữ. Nhiều người gọi đây là văn hóa, nhưng với thiển nghĩ của mình, người viết bài này cho rằng, nếu coi Văn miếu Quốc tử giám là nơi linh thiêng thì không nên phơi mặt chữ ra bên ngoài hè như vậy. Về bản chất, hiện tượng này với nạn bằng giả có chút tương đồng nào đó.

Nếu tìm được thầy cho chữ mà xin vào ngày đầu xuân là phúc lớn nên nó là nét văn hóa đẹp và cần làm. Còn xin – cho chữ như hiện nay chỉ giống như cái mốt của một thời. Mốt nào rồi cũng hết thời nhưng học chữ là muôn thuở.

Do vậy, cái mà chúng ta gọi là chữ bày la liệt trên các con phố chỉ là những bức họa chữ và người làm ra chúng là những người thợ viết, cao hơn là nghệ nhân viết chữ.

Quí thay, văn hóa thay khi mọi người chú tâm học Chữ thay vì rủ nhau đi xin chữ

Giao thừa Canh Dần – Tân Mão (ngày 03/02/2011)